company blog about Mingjiada Electronics Supply TI THS4130EVM Evaluation Module, Evaluation Of The THS4130 High-Speed Operational Amplifier

Mingjiada Electronics Supply TI THS4130EVM Evaluation Module, Evaluation Of The THS4130 High-Speed Operational Amplifier

Shenzhen Mingjiada Electronics Co., Ltd. — Long-term supplier of [TI] THS4130EVM: THS4130 High-Speed Operational Amplifier Evaluation Module. Product details for the THS4130EVM are as follows:

The THS4130EVM exemplifies PCB design and layout for high-speed operational amplifier applications. This evaluation board provides a complete circuit solution for high-speed op-amps, comprising the THS4130 high-speed operational amplifier, several passive components, and multiple functional modules and packages. It enables users to experiment, test, and validate various operational amplifier circuit implementations.

THS4130EVM Product Information:
Number of Channels per IC: 1 - Single Channel
Amplifier Type: Differential
Output Type: Differential
Slew Rate: 67V/µs
-3dB Bandwidth: 170MHz
Gain-Bandwidth Product: 215MHz
Current - Output/Channel: 85mA
Current - Supply (Main IC): 13mA
Voltage - Supply, Single/Dual (±): 4V to 33V, ±2V to 16.5V
IC/Parts Used: THS4130
Contents: Board
THS4130EVM Product Image:

THS4130EVM evaluation board measures 4.5 inches × 2.5 inches. Initially configured as a single-ended input amplifier, the outputs (Vo+ and Vo-) can be tested differentially or single-ended. Gain is set to 1 by default and can be altered by adjusting the ratio of feedback resistor to gain resistor. Users may validate filter designs or conduct other experiments using the multiple pad layouts on the THS4130EVM evaluation module board. Each input is equipped with a 50-ohm terminating resistor to ensure correct line impedance matching.

THS4130EVM Features:
Voltage supply operating range: 5 V to ±15 V operation
Single-ended and differential input/output capability
Nominal 50-ohm input/output termination resistors. Configurable according to application requirements.
Vocm direct input control
Vocm pin controllable via transformer centre tap
Shutdown pin controls JU1
Input/output transformer pads for converting single-ended signals to differential signals
High-precision balanced feedback and gain resistor pads (0.01% accuracy or better)
Low-pass filter implementation pads
Anti-aliasing filter implementation pads
Differential probe interfaces at input/output nodes
Multiple ground and signal test points on PCB
Schematic printed on EVM rear
Exemplary case study of high-speed amplifier PCB design and layout

THS4130EVM Supported Products:
Fully differential amplifiers
THS4130 — 150MHz fully differential input/output low-noise amplifier with shutdown function
High performance
Bandwidth: 170MHz (V CC = ±15V, G = 1V/V)
Slew Rate: 51 V/µs
Gain-Bandwidth Product: 215 MHz
Distortion: –102 dBc THD (at 2 V PP, 250 kHz)
Voltage Noise
1/f Voltage Noise Cutoff Frequency: 350 Hz
Input-Referred Noise: 1.25 nV/√Hz
Single Supply Operating Voltage Range: 5 V to 30 V
Quiescent Current (Shutdown): 860 µA (THS4130)
Temperature Range: –40°C to +85°C
Package: PowerPAD™ HVSSOP-8, SOIC-8, VSSOP-8

【Mingjiada Electronics】offers long-term supply of TI (THS4130EVM) high-speed amplifier evaluation modules. For further product information or sample procurement regarding the THS4130EVM, please visit Mingjiada Electronics' official website (https://www.integrated-ic.com/) for detailed supply information.